PRODUCT DATA:
DECK-O-FOAM - #325 |
|
|
|
|
|
|
|
|
DESCRIPTION
DECK-O-FOAM expansion joint filler is a flexible, lightweight, non-staining, polyethylene, closed-cell expansion joint filler. It is a chemical-resistant, ultraviolet stable, non-absorbent, low density, economical, compressible foam that offers an extended service life in both interior and exterior applications.
DECK-O-FOAM is supplied with a convenient, pre-scored removable strip to provide a uniform sealing reservoir in the joint. It also serves as a sealant bond-breaker and provides an economical alternative as an expansion joint in all concrete paving projects. It is compatible with all currently available cold-applied sealants.
USES
DECK-O-FOAM is ideal for use as an expansion, contraction, and/or isolation joint in swimming pool decks, curb and gutter work, floor slabs, pavement patch repair, sidewalks, driveways, plazas, parking decks, highways, and airport runways.
| FEATURES AND BENEFITS |
|
LEED INFORMATION |
|
TECHNICAL DATA**
TEST
METHOD |
TYPICAL
VALUE |
|
| Color | N/A |
Gray |
| Density | ASTM
D 1622 |
2.0 lb./ft.³ (32.04 kg/m³) |
| Compression | ||
| 10% Deflection | ASTM
D 3575 |
10
psi (69 KPa) max. |
| 80% Deflection | ASTM
D 3575 |
125
psi (862.49 KPa) max. |
| Tensile Strength | ASTM
D 3575 |
55
psi (379.50 KPa) |
| Water Absorption | ASTM
D 3575 |
0.5%
vol. max. |
| Temperature Stability | N/A |
-40º
F to 160 ºF (-40º C to 71º C) |
| ** These physical properties are typical, but should not be used in specifying material due to differences that could result from variations in testing methods. | ||
APPLICATION
Attach DECK-O-FOAM securely to the existing concrete slab, coping or form with
tape or mechanical fasteners prior to pouring the next slab. Make sure that
DECK-O-FOAM is level with the desired slab surfaces before finishing. If specifications
require the use of a cold-applied sealant, remove the pre-scored strip and apply
the sealant following the manufacturer's instructions.
| * PACKAGING (Standard Size Rolls) | |||
| 1/4" x 3" x 100' | 20 rolls/bale | 1/2" x 3" x 50' | 20 rolls/bale |
| 1/4" x 4" x 100' | 15 rolls/bale | 1/2" x 3 1/2" x 50' | 17 rolls/bale |
| 1/4" x 6" x 100' | 10 rolls/bale | 1/2" x 4" x 50' | 15 rolls/bale |
| 1/4" x 8" x 100' | 7 rolls/bale | 1/2" x 5" x 50' | 12 rolls/bale |
| 1/4" x 48" x 100' | 1 roll/bale | 1/2" x 6" x 50' | 10 rolls/bale |
| 1/2" x 8" x 50' | 7 rolls/bale | ||
| 1/2" x 48" x 50' | 1 roll/bale | ||
| * Special sizes available upon request. | |||
October 2008
LIMITED
WARRANTY
"DECK-O-SEAL®, A Division of W. R. MEADOWS, INC., warrants
at the time and place we make shipment, our material will be of
good quality and will conform with our published specifications
in force on the date of acceptance of the order." Read complete
warranty. Copy furnished upon request.
Disclaimer
The information contained herein is included for illustrative
purposes only, and to the best of our knowledge, is accurate and
reliable. DECK-O-SEAL cannot however under any circumstances make
any guarantee of results or assume any obligation or liability
in connection with the use of this information. As DECK-O-SEAL
has no control over the use to which others may put its product,
it is recommended that the products be tested to determine if
suitable for specific application and/or our information is valid
in a particular circumstance. Responsibility remains with the
architect or engineer, contractor and owner for the design, application
and proper installation of each product. Specifier and user shall
determine the suitability of products for specific application
and assume all responsibilities in connection therewith.